Search Results

An experimental study was undertaken to study exhaust emission from a lean-burn natural gas spark ignition engine. The possibility that such an engine may help to reduce exhaust emissions substantially by taking advantage of natural gas fuel properties, such as its antiknock properties and extended lean flammability limit compared to gasoline, was the main motivation behind the investigation. A four cylinder, automotive type spark ignition engine was used in the investigation. The engine was converted to operate on natural gas by replacing its fuel system with a gaseous carburetion system. A 3-way metal metrix catalytic converter was used in the engine exhaust system to reduce emission levels. The engine operated satisfactorily at an equivalence ratio as lean as 0.6, at all speeds and loads. As a result NOx emissions were significantly reduced. However, hydrocarbon emissions were high, particularly at very lean conditions and light loads.

As the federal regulations of on-road engine exhaust emissions become more and more stringent, the exhaust emissions of small utility engines are now under close study and are becoming subject to federal regulations. This paper reports the on-going research on emissions and test procedures for small utility engines at the University of Michigan. A group of small utility engines, selected by the National Fuels and Emissions Laboratory of the U.S. Environmental Protection Agency (EPA), were tested at various air/fuel ratios under steady state and transient operation. Mass rate of emissions of carbon monoxide (CO), carbon dioxide (CO2), total hydrocarbons (HC) and oxides of nitrogen (NOx) were measured using dilute sampling. The lean operation limit of some engines was studied to find a compromise among emissions, engine power, and engine life. Experimental research was also undertaken to study emission control techniques; such as catalytic conversion, air injection, and fuel injection.

A hybrid car is conceptually described and analyzed which meets the goal of a factor of three improvement in fuel economy set by the government-industry collaboration, Partnership for a New Generation of Vehicles, announced Sept. 29, 1993. This car combines an internal combustion engine with a low-energy, but high-power capacity, storage unit, such as a capacitor or flywheel. The storage capacity is one-half kWh. All energy requirements are ultimately met from the fuel tank. Essentially all the performance achievements of current conventional cars are met by this hybrid. Two versions of the hybrid are considered: one in which the vehicle loads are the same as those of the average 1993 car, but the drive train is replaced with a hybrid system, and one, where, in addition, the vehicle loads are reduced, at fixed performance and interior volume, to levels slightly beyond the best achievements in current production vehicles.

Cost reduction, quality improvement, and regulatory compliance are well-recognized competitive issues. Companies must excel along each of these fronts while operating in an environment of rapid and multi-faceted change, limited financial and human capital, and increasing product development time pressure. In addition, consumers are demanding automobiles that provide greater performance, function, and comfort while emitting lower emissions, consuming fewer gallons of gasoline, injuring fewer humans, and requiring fewer dollars to build and purchase. A solution to these seemingly conflicting objectives is to take a systems view of the product and industry. This paper explores the material decision process so that manufacturers, component suppliers, and material providers may better understand the interlocking web of compromises that shape the pursuit of value-added alternatives and avoidance of unprofitable compromises.

This study is to explore the application of electrorheology (ER) to the real-time control of damping forces that are transmitted through the nose landing gear for an F-106B aircraft. The main part of the landing gear is a strut that consists of a pneumatic spring and an ER controlled damper that is situated on the strut centerline and applies a force directly opposing the vertical displacement of the nose wheel. The damping element rotates in response to strut displacement, employing a co-axial arrangement of stator and rotor plates connected to the opposing electrodes in the control circuit. The vertical displacement is converted into rotation of the damper through a screw-nut mechanism. The ER fluid between the electrodes is thus engaged in shear along circumferential lines of action. This design results in a fast time response and a high ratio of strut forces achieved under ER- vs. zero-field control. Compact size and simplicity in fabrication are also attained.

An experimental study was undertaken to investigate emissions of hydrocarbons, oxides of nitrogen, carbon monoxide, and methane hydrocarbons emitted by natural gas fueled engines and the extent of their conversion in catalysts. Two engines were used in the study: a four cylinder, 1.6 liter, spark ignition engine and a modified version of the same engine with only one of the cylinders operating at 0.4 liter capacity. Two-way and three-way catalysts were used to treat exhaust gases leaving the engine. Natural gas was supplied through gas carburetors operated at regulated pressures and supplying air-fuel ratios in the desired range. The results of the investigation showed that oxides of nitrogen could not be reduced in a three-way catalyst to the levels found in gasoline fueled engines when the operating air-fuel ratio was stoichiometric.

The automobile industry has been using high-density polyethylene (HDPE) as a material to fabricate fuel tanks. Because untreated HDPE is permeable to the primary constituents of gasoline, these fuel tanks are now being produced with various barrier technologies that significantly reduce this permeation rate. Four currently available barrier technologies are fluorination, sulfonation, coextrusion, and the laminar barrier technology. These technologies have successfully proven to decrease the permeation rate of pure gasoline. However, it is suspected that their effectiveness may be reduced when alcohols are introduced into the fuel blend. In this work, we determine the permeation rates of gasoline-alcohol fuel blends through HDPE by conducting tests on 22-gallon HDPE fuel tanks and on small HDPE bottles fabricated with and without these barrier technologies. The goal of this study is to provide a comprehensive evaluation of these four barrier technologies.

A Pore Fuel Injector Deposit (PFID) test has been developed which provides repeatable results. The test can discriminate gasolines with differing fuel injector fouling tendencies in vehicles. Results confirm previous work that added mono-and diolefins increase deposit growth. The test is also able to evaluate the performance of additives. Other factors found to affect injector deposit formation include: injector soak temperature, injector soak pressure, weeping vs non-weeping injectors, and the presence of oxygen around the injector pintle. The PFID test can be run in about one quarter the time needed to evaluate fuels in vehicle and dynamometer tests.(1)

A cylindrical combustion bomb with dynamic charging system and electro-hydraulic sampling valve is used to study the effects of turbulence on hydrocarbon (HC) emissions from a quench layer and from artificial crevices. The turbulence level is varied by changing the delay time between induction of combustible charge and ignition. Propane-air mixtures were studied over an initial pressure range of 150 to 500 kPa and equivalence ratios of 0.7 to 1.4. Sampling valve experiments show that quench-layer fuel hydrocarbons are extensively oxidized within 5 ms of flame arrival under laminar conditions and that turbulence further reduces the already low level. Upper limit estimates of the residual wall layer HC concentration show that residual quench layer hydrocarbons are only a small fraction of the exhaust HC emission.

Secondary injection in a diesel engine is defined as the introduction of additional fuel into the combustion chamber after the end of the main injection. It is usually caused by residual pressure waves in the high-pressure pipe line connecting the pump and injector. When these waves exceed the injector opening pressure, secondary injection occurs. Tests revealed that the U.S. Army TACOM single-cylinder engine used in this investigation, fitted with an American Bosch injection system, had secondary injection within the normal engine operating region. The pump spill ports and delivery valve were redesigned to eliminate secondary injection, in accordance with previously reported work. Comparative tests of both the conventional and modified injection systems were run on the same engine, and the effects of secondary injection on engine power, economy, and exhaust emissions were determined.

After-injection is the introduction of additional fuel to the combustion chamber after the end of the main injection. It is a persistent diesel fuel injection problem which usually results in reduced engine power and economy and increased emissions. After-injection is caused by uncontrolled pressure transients at the injector after the opening of the pump spill port. These pressure transients are related to the wave propagation phenomena in the high-pressure pipeline connecting the pump and injector. Use of experimental trial-and-error methods in attempts to control this phenomenon has met with limited success. The analytical control method described in another paper is used to determine design means by which after-injection may be controlled. Further investigation and evaluation of two design changes which release the injection system excess elastic energy in a controlled manner are considered herein. One design change is the addition of a control valve in the pump delivery chamber.

A theoretical digital simulation of a conventional diesel fuel injection system has been developed. The influence of such factors as wave propagation phenomena, pipe friction, and cavitation are included. The computer results are compared with transient pressures as measured on an actual fuel injection system operated on a test bench. The comparisons show the accuracy and validity of this simulation scheme. Special attention is given to some of the important factors that affect the accuracy of the simulation model. These include the effect of pressure on the fuel bulk modulus and wave speed, the pipe line residual pressure, and the coefficient of discharge of important orifices.

Possible mechanisms for smoke formation in the diesel engine are discussed. Emphasis is placed on the effects of some engine and fuel factors on carbon formation during the course of combustion, including cetane number, fuel volatility, air charge temperature, and after-injection. The tests were made with a single-cylinder, open chamber research engine, with three fuels, covering a wide range of inlet air temperatures and pressures. There is evidence that smoke intensity increased with increase in the cetaine number of the fuels with inlet air temperatures near atmospheric. Increase in the air charge temperature caused an increase in smoke intensity for volatile fuels and had an opposite effect on less volatile fuels for the open chamber engine used. The smoke intensity was found to increase dramatically with after-injection, with all other parameters kept constant. The concept that flame cooling is the main cause for smoke formation is examined.

APPLICATION of nuclear energy for civilian automotive uses has possibilities, these authors say. Nuclear power for automotive applications, they feel, is technically feasible now where size and weight are not prime considerations; where size and weight are major parameters, discoveries of new materials for construction of nuclear-power reactors must be made. New materials are needed for reactor fuels, heat extractants, neutron reflectors, reactor construction materials, controls, and radiation shields which must have unique nuclear properties in addition to conventional engineering properties. This paper presents nuclear automotive propulsion devices in terms of technologies now available. The necessary radiation-shielding mass and weight requirements are presented for an ideal point-source nuclear-heat-power engine.

A METHOD is described in this paper by which the rates of gear wear under different conditions can be determined by the use of the radioactive tracer technique. With this method one can measure the minutest amount of wear at loads and speeds much below critical destructive conditions. This method makes possible the continuous determination of rates of gear wear at all loads and speeds in actual full-scale units. In this investigation, the radioactive tracer technique has been used to determine the rates of gear wear when using a straight mineral oil and when using an extreme-pressure gear lubricant.